GY-63_MS5611/libraries/Cozir

Cozir

Arduino library for COZIR range of temperature, humidity and CO2 sensors.

Description

The Cozir library is experimental as I do not have a sensor to test the library. The polling mode as used in the examples seems to work quite well as this is tested by DirtGambit.

This library supports only the Serial interface. An I2C based library will be written when I have access to a Cozir sensor that supports I2C. Idea is to make the interface identical if possible.

Notes

• the CozirDemoHWSerial.ino example needs to run on a MEGA or a Teensy, at least a board with more than one Serial port.
• Read the datasheet before using this library. It helps to understand the working of the Cozir sensor.

Interface

Read the datasheet (again).

Constructor and initialisation

• COZIR(Stream * str) constructor.
• void init() sets operatingMode to CZR_POLLING.
• bool isInitialized() returns true if enough time has passed after the call to init() for the sensor.

Operating mode

• void setOperatingMode(uint8_t mode) set the operating mode either to CZR_COMMAND, CZR_POLLING or CZR_STREAMING
• uint8_t getOperatingMode() returns the mode set, CZR_STREAMING is the default. Please note that init() sets the operating mode to CZR_POLLING.

Core

• float celsius() idem.
• float fahrenheit() idem, 'wrapper' around celsius()
• float humidity() idem.
• float light() idem.
• uint32_t CO2() idem.
• uint16_t getPPMFactor() returns 1, 10, 100 See Page 14.

Calibration

Read datasheet before using these functions:

• uint16_t fineTuneZeroPoint(uint16_t v1, uint16_t v2)
• uint16_t calibrateFreshAir()
• uint16_t calibrateNitrogen()
• uint16_t calibrateKnownGas(uint16_t value)

Calibration NOT Recommended

Following 3 functions are NOT RECOMMENDED by the datasheet. Feel free to uncomment and use at your own risk. Read datasheet before using these functions:

• uint16_t calibrateManual(uint16_t value)
• uint16_t setSpanCalibrate(uint16_t value)
• uint16_t getSpanCalibrate()

Digifilter

use with care, read datasheet before use.

value	meaning
0	Special, see datasheet page ...
1	fast, but can be noisy
32	default, good average
255	slow, max smoothed

• void setDigiFilter(uint8_t value)
• uint8_t getDigiFilter()

Streaming MODE

Warning: Not tested ,

• void setOutputFields(uint16_t fields) Sets the fields in the output stream as a 16 bit mask. See table below.
• void clearOutputFields() clears all the fields.
• uint16_t getOutputFields() returns the 16 bit mask of set output fields.
• bool inOutputFields(uint16_t field) returns true if the field is set.
• void getRecentFields() After a call to getRecentFields() you must read the serial stream yourself. The internal buffer of this Class cannot handle the possible large output. Lines can be over 100 bytes long!

The fields must be set as a bit mask, the order of the fields in the output is undetermined. So one need to parse the output of the sensor carefully.

Field	Value	Notes
CZR_LIGHT	0x2000
CZR_HUMIDITY	0x1000
CZR_FILTLED	0x0800
CZR_RAWLED	0x0400
CZR_MAXLED	0x0200
CZR_ZEROPOINT	0x0100
CZR_RAWTEMP	0x0080
CZR_FILTTEMP	0x0040
CZR_FILTLEDSIGNAL	0x0020
CZR_RAWLEDSIGNAL	0x0010
CZR_SENSTEMP	0x0008
CZR_FILTCO2	0x0004
CZR_RAWCO2	0x0002
CZR_NONE	0x0001	reset
CZR_HTC	0x1082	shortcut
CZR_ALL	0x3FFE	debug

EEPROM

Read datasheet Page 11-12 about the addresses and their meaning. Use with care.

In 0.3.0 the EEPROM function have been replaced by specific accessor functions. Read datasheet for the details.

• void setAutoCalibrationPreload(uint16_t value)
• uint16_t getAutoCalibrationPreload()
• void setAutoCalibrationInterval(uint16_t value)
• uint16_t getAutoCalibrationInterval()
• void setAutoCalibrationOn()
• void setAutoCalibrationOff()
• bool getAutoCalibration()
• void setAutoCalibrationBackgroundConcentration(uint16_t value)
• uint16_t getAutoCalibrationBackgroundConcentration()
• void setAmbientConcentration(uint16_t value)
• uint16_t getAmbientConcentration()
• void setBufferClearTime(uint16_t value)
• uint16_t getBufferClearTime()

EEPROM addresses used by above functions.

Read datasheet for the details.

Name	Address	Default	Notes
AHHI	0x00	?	reserved
ANLO	0x01	?	reserved
ANSOURCE	0x02	?	reserved
ACINITHI	0x03	87
ACINITLO	0x04	192
ACHI	0x05	94
ACLO	0x06	128
ACONOFF	0x07	0
ACPPMHI	0x08	1
ACPPMLO	0x09	194
AMBHI	0x0A	1
AMBLO	0x0B	194
BCHI	0x0C	0
BCLO	0x0D	8

Miscellaneous

• void getVersionSerial() requests version over serial. The user should read (and parse) the serial output as it can become large. Also the user must reset the operating mode either to CZR_POLLING or CZR_STREAMING
• void getConfiguration() requests configuration over serial. The user should read (and parse) the serial output as it can become large. Also the user must reset the operating mode either to CZR_POLLING or CZR_STREAMING

Future

• test test test test and ...
• add a setEEPROMFactoryDefault()?
• example two Cozir sensors
• example Cozir with I2C display?
• build a Arduino COZIR simulator for testing.
• Cozir I2C class for newer generation ~ same interface

Operation

See examples.

Test sensor

People who have a spare sensor for me, or are willing to run tests, please contact me.