mirror of
https://github.com/RobTillaart/Arduino.git
synced 2024-10-03 18:09:02 -04:00
174 lines
5.7 KiB
Markdown
174 lines
5.7 KiB
Markdown
|
|
[](https://github.com/marketplace/actions/arduino_ci)
|
|
[](https://github.com/RobTillaart/GY521/actions/workflows/arduino-lint.yml)
|
|
[](https://github.com/RobTillaart/GY521/actions/workflows/jsoncheck.yml)
|
|
[](https://github.com/RobTillaart/GY521/blob/master/LICENSE)
|
|
[](https://github.com/RobTillaart/GY521/releases)
|
|
|
|
|
|
# GY521
|
|
|
|
Arduino library for I2C GY521 accelerometer-gyroscope sensor a.k.a. MCU-6050.
|
|
|
|
|
|
## Description
|
|
|
|
Experimental library for GY521 a.k.a. MCU-6050.
|
|
|
|
Library is work in progress, in fact it is extracted and extended from an old project.
|
|
It needs to be tested a lot more.
|
|
|
|
|
|
#### Examples
|
|
|
|
- **GY521_angle** read angleX, angleY, angleZ.
|
|
- **GY521_performance** measure performance.
|
|
- **GY521_pitch_roll_yaw** to get pitch roll yaw.
|
|
- **GY521_readCalibration_1** read calibration values / errors for a flat sensor.
|
|
- **GY521_readCalibration_2** generate calibration code snippet.
|
|
- **GY521_test_1** test working of the sensor.
|
|
- **GY521_test_2** test set/get functions.
|
|
|
|
|
|
## Breakout board
|
|
|
|
From left to right
|
|
|
|
| pin | pinName | description | notes |
|
|
|:-----:|:---------:|:------------------|:-------:|
|
|
| 0 | VCC | +5V |
|
|
| 1 | GND | ground |
|
|
| 2 | SCL | I2C clock |
|
|
| 3 | SDA | I2C data |
|
|
| 4 | XDA | auxiliary data | see datasheet
|
|
| 5 | XCL | auxiliary clock | see datasheet
|
|
| 6 | AD0 | address |
|
|
| 7 | INT | interrupt |
|
|
|
|
|
|
#### Address
|
|
|
|
AD0 connected to GND => 0x68
|
|
AD0 connected to VCC => 0x69
|
|
|
|
|
|
## Calibration (short version for now)
|
|
|
|
1. load and run calibration example
|
|
it shows a header containing 6 numbers and 10 lines of 8 numbers
|
|
1. wait until the middle 6 of the longer lines stabilize (should all be 0)
|
|
1. copy the 6 numbers above the axe aye aze as these are the numbers needed.
|
|
|
|
|
|
## Interface
|
|
|
|
```cpp
|
|
#include "GY521.h"
|
|
```
|
|
|
|
### Constructor
|
|
|
|
- **GY521(uint8_t address = 0x69, , TwoWire \*wire = &Wire)** Constructor with default address.
|
|
0x68 is also a valid address. The wire argument is optional to select Wire1 Wire2 etc. on some boards.
|
|
- **bool begin(uint8_t sda, uint8_t scl)** begin for ESP32 et al. Returns true if address can be found on I2C bus.
|
|
- **bool begin()** Returns true if address can be found on I2C bus.
|
|
- **bool isConnected()** returns true if device can be found on I2C bus.
|
|
- **void reset()** set all internal values to 0 and throttle time to 10 ms.
|
|
- **bool wakeUp()** idem.
|
|
|
|
|
|
### Throttle
|
|
|
|
- **void setThrottle(bool throttle = true)** throttle to force "delay" between reads.
|
|
- **bool getThrottle()** returns true if throttle mode is set.
|
|
- **void setThrottleTime(uint16_t ti )** throttle time in milliseconds, max = 65535 = 1++ minute
|
|
- **uint16_t getThrottleTime()** returns throttle time set.
|
|
|
|
|
|
### Read
|
|
|
|
#### Set before read
|
|
|
|
- **bool setAccelSensitivity(uint8_t as)** as = 0, 1, 2, 3 ==> 2g 4g 8g 16g
|
|
- **uint8_t getAccelSensitivity()** returns 0, 1, 2, 3
|
|
- **bool setGyroSensitivity(uint8_t gs)** gs = 0,1,2,3 ==> 250, 500, 1000, 2000 degrees/second
|
|
- **uint8_t getGyroSensitivity()** returns 0, 1, 2, 3
|
|
|
|
|
|
#### Actual read
|
|
|
|
- **int16_t read()** returns status = GY521_OK on success.
|
|
- **int16_t readAccel()** read accelerometer only to speed up interaction. This call does update the throttle timer.
|
|
returns status = GY521_OK on success.
|
|
- **int16_t readGyro()** read gyroscope only to speed up interaction. This call does update the throttle timer.
|
|
returns status = GY521_OK on success.
|
|
Note: for pitch roll yaw you need to call **read()**.
|
|
- **int16_t readTemperature()** read temperature only, does **not** update the throttle timer.
|
|
returns status = GY521_OK on success.
|
|
- **uint32_t lastTime()** last time sensor is actually read. In milliseconds. Not updated by readTemperature().
|
|
|
|
Since version 0.3.8 the **read()** and **readGyro()** function is updated to keep the range of **getPitch()**,
|
|
**getRoll()** and **getYaw()** in the range 0..360 degrees. (Issue #36).
|
|
Problem is that with continuous rotation in a same direction internal variables will overflow and new
|
|
movements (angles) will get lost as insignificant digits.
|
|
|
|
|
|
#### Call after read
|
|
|
|
Note that multiple calls will return the same value. One must explicitly call **read()** to get new values.
|
|
|
|
- **float getAccelX()** idem
|
|
- **float getAccelY()** idem
|
|
- **float getAccelZ()** idem
|
|
- **float getAngleX()** idem
|
|
- **float getAngleY()** idem
|
|
- **float getAngleZ()** idem
|
|
- **float getTemperature()** idem
|
|
- **float getGyroX()** idem
|
|
- **float getGyroY()** idem
|
|
- **float getGyroZ()** idem
|
|
- **float getPitch()** idem. Returns 0.00 - 359.99.
|
|
- **float getRoll()** idem. Returns 0.00 - 359.99.
|
|
- **float getYaw()** idem. Returns 0.00 - 359.99.
|
|
|
|
|
|
### Register access
|
|
|
|
Read the register PDF for the specific value and meaning of registers.
|
|
|
|
- **uint8_t setRegister(uint8_t reg, uint8_t value)**
|
|
- **uint8_t getRegister(uint8_t reg)**
|
|
|
|
|
|
## documents
|
|
|
|
- check details - MPU-6000-Register-Map1.pdf
|
|
|
|
|
|
## Operation
|
|
|
|
See examples, use with care
|
|
|
|
|
|
## Future
|
|
|
|
#### Must
|
|
|
|
- improve documentation
|
|
|
|
#### Should
|
|
|
|
- test test and test ...(ESP too)
|
|
|
|
#### Could
|
|
|
|
- calibrate sketch could print code snippet to include...
|
|
|
|
#### Wont
|
|
|
|
- look for maths optimizations (atan, hypot, performance)
|
|
- ==> hypot optimized.
|
|
- other ideas affect accuracy, so unless new ideas arise.
|
|
- calibrate function in the lib
|
|
- not as lib will grow too large.
|