GY-63_MS5611/libraries/MATRIX7219

MATRIX7219

Arduino Library for controlling one or more 8x8 LED MATRIX with a MAX7219.

Description

This experimental library provides an easy control to 8x8 MATRIX boards. It is pretty minimalistic for now as the user still has to do bit math to get the right lights on as one can only set 8 LEDS at a time.

For the future two (derived) classes are planned:

• a class that is optimized to use for a single 8x8 matrix.
• a class that buffers the state of the LEDS, allowing more functionality.

Tests

It is tested with an UNO and a single 8x8 matrix and a 4x 8x8 matrix-chain. During tests it became clear that the orientation of the matrices I used, seen from the IN connector was different. These insights lead to the implementation of the inverse, reverse and swap functions.

Related

• TODO

Tested

Tested on Arduino UNO.

Interface

#include "MATRIX7219.h"

Not all functionality works, matrix parameter et al.

• MATRIX7219(uint8_t dataPin, uint8_t selectPin, uint8_t clockPin, uint8_t matrices) Constructor, initializes IO pins and the number of 8x8 matrices on same pins.
• void begin() resets the internals of the connected device.
• uint8_t getMatrixCount() returns number of matrices set in constructor. Convenience function.
• void setBrightness(uint8_t bright = 2) set bright = 0..15 for all matrices. Default is a relative low intensity.
• void displayOff() switches on low power mode == all LEDs off. Leaves all registers the same. Can be used to blink the display, get attention.
• void displayOn() switches display on again.
• void displayTest(bool on = false) sets all LEDs on full brightness. Used to verify all LEDS still work. Or to implement a flashy alarm. Default value is false ==> normal mode.
• void clear() clear all matrices.
• void setRow(uint8_t row, uint8_t value, uint8_t matrix) set a value to a certain row of a certain matrix.

Invert, reverse and swap.

For adapting the layout if needed.

• void setInvert(bool invert) invert the output. Default = false.
• bool getInvert() get current setting.
• void setReverse(bool rev) reverse the output. Default = false.
• bool getReverse() get current setting.
• void setSwap(bool swap) swaps row n with (8-n).
• bool getSwap() get current setting.

Performance

0.1.0 UNO

MATRIX7219_performance.ino with UNO 16 MHz

board	function	time (us)	notes
UNO	begin	796
UNO	clear	1572
UNO	count	4
UNO	setRow(255)	204	setReverse has minimal influence
UNO	setRow(0)	200
UNO	setBrightness	208

0.1.1 UNO

Optimized registers for UNO (for AVR from FastShiftOut). 2.5 to 4.2 times faster. (price: a few bytes storage).

board	function	time (us)	notes
UNO	begin	196	2.5x
UNO	clear	368	4.2x
UNO	count	4	idem
UNO	setRow(255)	56	3.5x
UNO	setRow(0)	56	3.5x
UNO	setBrightness	56	3.5x

0.1.1 ESP32

First test ESP32

board	function	time (us)	notes
ESP32	begin	37
ESP32	clear	47
ESP32	count	2
ESP32	setRow(255)	12
ESP32	setRow(0)	8
ESP32	setBrightness	8

Future

Must

• improve documentation

Should

• create a derived class with a buffer => 8 bytes per Matrix.
  • goal is to have setPixel(x,y) and clearPixel(x,y)
  • design first (performance)

Could

• examples
  • 8x8 as debugger (dump variables)
• add unit tests
  • need simulator / mock-up
• defaults for invert, reverse, swap? (false).

Wont (unless requested)

• create a derived class for a single 8x8 matrix.
  • if performance gain is enough?
• store last set brightness.
  • uint8_t getBrightness()
  • not needed yet