GY-63_MS5611/libraries/MCP23S17

MCP23S17

Arduino library for MCP23S17 16 channel SPI port expander.

Description

This experimental library gives easy control over the 16 pins of a (SPI) MCP23S17 chip.

This IC is strongly related to the MCP23017 I2C port expander - https://github.com/RobTillaart/MCP23017_RT Programming Interface is kept the same as much as possible.

Interface

Constructor

• MCP23S17(uint8_t select, uint8_t dataIn, uint8_t dataOut, uint8_t clock, uint8_t address = 0x00) constructor SW SPI.
• MCP23S17(uint8_t select, SPIClass* spi) constructor HW SPI with explicit SPI interface selected.
• MCP23S17(uint8_t select, uint8_t address = 0x00, SPIClass* spi = &SPI) constructor HW SPI with optional address pins and SPI interface.
• bool begin() returns true if successful.
• bool isConnected() returns true if connected, false otherwise. (dummy for compatibility reasons)
• uint8_t getAddress() returns the address set in the constructor. Default = 0, range = 0..7.

The two constructors allow to call 4 different constructors.

- MCP23S17(10);            // select pin only
- MCP23S17(10, 7);         // select pin + address pins
- MCP23S17(10, 7, &SPI2);  // select pin + address pins + SPI port
- MCP23S17(10, &SPI2);     // select pin + SPI port

sharing select lines

(not tested) Technically two chips could use the same select pin and a different address. The constructors would allow to setup such a configuration. I assume that this is less used and IMHO not recommended.

Single pin interface

• bool pinMode(uint8_t pin, uint8_t mode) pin = 0..15, mode = INPUT, OUTPUT. Returns true if successful.
• bool digitalWrite(uint8_t pin, uint8_t value) pin = 0..15, value = LOW(0) HIGH (!0). Returns true if successful.
• uint8_t digitalRead(uint8_t pin) pin = 0..15, returns LOW or HIGH, might set the lastError();
• bool setPolarity(uint8_t pin, bool reversed) pin = 0..15, set reversed flag. Returns true if successful.
• bool getPolarity(uint8_t pin, bool &reversed) pin = 0..15, reads reversed flag. Returns true if successful.
• bool setPullup(uint8_t pin, bool pullup) pin = 0..15, set pull-up flag. Returns true if successful.
• bool getPullup(uint8_t pin, bool &pullup) pin = 0..15, reads pull-up flag. Returns true if successful.

8 pins interface

• bool pinMode8(uint8_t port, uint8_t value) port = 0..1, value = 0..255. Returns true if successful.
• bool write8(uint8_t port, uint8_t value) port = 0..1, value = 0..255. Returns true if successful.
• uint8_t read8(uint8_t port) port = 0..1, reads 8 pins into one byte.
• bool setPolarity8(uint8_t port, uint8_t mask) port = 0..1, sets polarity for 8 channels at once. Returns true if successful.
• bool getPolarity8(uint8_t port, uint8_t &mask) port = 0..1, reads polarity of 8 channels at once. Returns true if successful.
• bool setPullup8(uint8_t port, uint8_t mask) port = 0..1, sets pull-up for 8 channels at once. Returns true if successful.
• bool getPullup8(uint8_t port, uint8_t &mask) port = 0..1, reads pull-up for 8 channels at once. Returns true if successful.

16 pins interface

• bool pinMode16(uint16_t value) value = 0..0xFFFF, returns true if successful. Returns true if successful.
• bool write16(uint16_t value) value = 0..0xFFFF, returns true if successful. Returns true if successful.
• uint16_t read16() reads 16 pins into an uint16_t.
• bool setPolarity16(uint16_t mask) sets polarity for 16 channels. Returns true if successful.
• bool getPolarity16(uint16_t &mask) reads polarity of 16 channels. Returns true if successful.
• bool setPullup16(uint16_t mask) sets pull-up for 16 channels. Returns true if successful.
• bool getPullup16(uint16_t &mask) reads pull-up for 16 channels. Returns true if successful.

IO Control Register

Since 0.2.3 the library supports setting bit fields in the IO control register. Read the datasheet carefully!

• void enableControlRegister(uint8_t mask)
• void disableControlRegister(uint8_t mask)

constant	mask	description
MCP23S17_IOCR_BANK	0x80	Controls how the registers are addressed.
MCP23S17_IOCR_MIRROR	0x40	INT Pins Mirror bit.
MCP23S17_IOCR_SEQOP	0x20	Sequential Operation mode bit.
MCP23S17_IOCR_DISSLW	0x10	Slew Rate control bit for SDA output.
MCP23S17_IOCR_HAEN	0x08	Hardware Address Enable bit (MCP23S17 only).
MCP23S17_IOCR_ODR	0x04	Configures the INT pin as an open-drain output.
MCP23S17_IOCR_INTPOL	0x02	This bit sets the polarity of the INT output pin.
MCP23S17_IOCR_NI	0x01	Not implemented.

Error codes

If one of the above functions return false, there might be an error.

• int lastError() Above functions set an error flag that can be read with this function.
  Reading it will reset the flag to MCP23S17_OK.

NAME	VALUE	DESCRIPTION
MCP23S17_OK	0x00	No error
MCP23S17_PIN_ERROR	0x81
MCP23S17_I2C_ERROR	0x82	(compatibility)
MCP23S17_VALUE_ERROR	0x83
MCP23S17_PORT_ERROR	0x84
MCP23S17_REGISTER_ERROR	0xFF	low level.

Operation

See examples.

Future

must

• improve documentation
  • references to I2C version?

should

• keep functional in sync with MCP23017_RT

could

• check need for writing in all functions (Polarity / pullup)
  • check if bit mask changes.
  • what is performance gain vs footprint?
• implement ESP32 specific support in begin()
  • see MCP_ADC.begin()
  • SW_SPI is roughly equal in performance as HW SPI on ESP32.
• investigate and reimplement the INPUT_PULLUP for pinMode() ?

wont

• check address range in constructor.