GY-63_MS5611/libraries/TinyKT0803

TinyKT0803

Arduino Library for KT0803 and KT0803K FM transmitter. Tiny85 edition.

Legal point of attention

In different countries there are different laws with respect to using transmitting devices and their range. Please inform yourself of the local rules and laws if and how you may or may not use a device like the KT0803 in your projects, either hobby, commercial or otherwise.

Description

This is an EXPERIMENTAL port to the Tiny85/45/25 processor of - https://github.com/RobTillaart/KT0803

The library is verified to work - See issue #2
There are two points of attention:

• ATTiny85 needs a 500 ms delay to initialize I2C to communicate properly (assuming 1 MHz clock)
• ATTiny85 needs a decoupling capacitor 100-300 nF between RESET and GND and a 10K resistor between VDC and RESET

Note: The KT0803 library will be leading in development and this one will follow. The interface section below is identical except for the constructor.

Interface

#include "TinyKT0803.h"

Constructor

• TinyKT0803() constructor.
• TinyKT0803K() constructor.
• bool begin(float freq = 90.0, bool mute = true) initializes the library. Furthermore it checks if the deviceAddress is available on the I2C bus. Default it sets the frequency to 90 MHz and mutes the signal. Returns true if deviceAddress is found on the bus, false otherwise.
• bool isConnected() test to see if deviceAddress is found on the I2C-bus.

Frequency

• bool setFrequency(float MHz) converts the frequency in MHz to call setChannel(channel). The value of channel is rounded off depending on the resolution of the device. Returns false if MHz is out of range or setChannel() fails.
• float getFrequency() returns the current frequency in MHz, can be slightly different from the set value due to rounding math mentioned above. The return value is derived from a call to getChannel()
• bool setChannel(uint16_t channel) writes the channel to broadcast on to the device. This involves two or three writes to different device registers.
• uint16_t getChannel() reads the selected channel from the device and returns it.

PGA

Read Datasheet.

The KT0803K has a PGA_LSB (2 bits) setting, which allows setting the gain with single (1) dB steps. This is not yet implemented in the library.

• bool setPGA(uint8_t pga) sets gain according to table below. Returns false if pga is out of range (0..7).
• uint8_t getPGA() returns 0..7, default 0.

PGA	gain	notes
111	12dB
110	8dB
101	4dB
100	0dB
000	0dB	default
001	-4dB
010	-8dB
011	-12dB

RFGain

Read Datasheet.

Note: the RFGain value (4 bits) is distributed over three registers. PA_BIAS (register 0x05) is only supported in the KT0803K device. It is not yet supported in the library.

• bool setRFGain(uint8_t rfgain) sets rfgain according to table below. Returns false if rfgain is out of range (0..15).
• uint8_t getRFgain() returns 0..15, default 15.

RFGAIN	RFout	PA_BIAS = 1	notes
0000	95.5 dBuV	-
0001	96.5 dBuV	-
0010	97.5 dBuV	-
0011	98.2 dBuV	-
0100	98.9 dBuV	-
0101	100.0 dBuV	-
0110	101.5 dBuV	-
0111	102.8 dBuV	-
1000	105.1 dBuV	107.2 dBuV
1001	105.6 dBuV	108.0 dBuV
1010	106.2 dBuV	108.7 dBuV
1011	106.5 dBuV	109.5 dBuV
1100	107.0 dBuV	110.3 dBuV
1101	107.4 dBuV	111.0 dBuV
1110	107.7 dBuV	111.7 dBuV
1111	108.0 dBuV	112.5 dBuV	default

Region selection

Read datasheet for details.

Note that not all frequencies are allowed in all regions / countries!

The first four are convenience wrappers for setPHTCNST() If some region is missing please let me know the details and I can add a wrapper for it.

• void setEurope()
• void setAustralia()
• void setUSA()
• void setJapan()
• bool setPHTCNST(bool on) See table below.
• bool getPHTCNST() returns set value.

PHTCNST	time	Region
0	75 μs	USA, Japan, (default)
1	50 μs	Europe, Australia

PilotToneAdjust

Read datasheet.

• bool setPilotToneAdjust(uint8_t mode) HIGH = 1 LOW = 0
• uint8_t getPilotToneAdjust()

Mute

Default the device is not muted, but begin() will default mute it. See interface section above.

• bool setMute(bool mute) enables or disables the transmitting by muting the signal.
• bool getMute() returns the current state of muting.

Preference channels

The device and library do not implement the persistant store of user selectable preferences (frequencies or channels). This can be implemented by the user in EEPROM or another persistent medium.

Think of a class that holds an array of channels and optional descriptions. A minimal hardcoded preset sketch is in the examples.

Derived classes

A derived class TinyKT0803K class is created, with some extended functions.

The KT0803L will work as it is backwards compatible with KT0803K. It has far more registers in use than the KT0803/K.

The KT0803M is identical to the KT0803K (no new registers), so a derived class is straightforward.

Interface KT0803K

(not tested), check datasheet.

Mono Stereo

• bool setMono() idem
• bool setStereo() idem
• bool isStereo() idem

Bass

• **bool setBass(uint8_t bass); // 0..3 = 0, 5, 11, 17 dB
• uint8_t getBass() idem

Misc

• bool powerOK() idem
• bool silenceDetected() idem

Future

See - https://github.com/RobTillaart/KT0803

Support

If you appreciate my libraries, you can support the development and maintenance. Improve the quality of the libraries by providing issues and Pull Requests, or donate through PayPal or GitHub sponsors.

Thank you,