mirror of
https://github.com/RobTillaart/Arduino.git
synced 2024-10-03 18:09:02 -04:00
186 lines
6.4 KiB
Markdown
186 lines
6.4 KiB
Markdown
|
|
||
|
|
[](https://github.com/marketplace/actions/arduino_ci)
|
||
|
|
[](https://github.com/RobTillaart/AM2315C/actions/workflows/arduino-lint.yml)
|
||
|
|
[](https://github.com/RobTillaart/AM2315C/actions/workflows/jsoncheck.yml)
|
||
|
|
[](https://github.com/RobTillaart/AM2315C/blob/master/LICENSE)
|
||
|
|
[](https://github.com/RobTillaart/DHT20/releases)
|
||
|
|
|
||
|
|
|
||
|
|
# AM2315C
|
||
|
|
|
||
|
|
Arduino library for I2C AM2315C temperature and humidity sensor.
|
||
|
|
|
||
|
|
|
||
|
|
## Description
|
||
|
|
|
||
|
|
The AM2315C is a humidity and temperature sensor.
|
||
|
|
|
||
|
|
Warning: this sensor is not compatible with the AM2315.
|
||
|
|
|
||
|
|
The sensor has a fixed address of **0x38**.
|
||
|
|
|
||
|
|
The library must be initiated by calling the **begin()** function,
|
||
|
|
or **begin(dataPin, clockPin)** for **ESP32** and similar platforms.
|
||
|
|
|
||
|
|
Thereafter one has to call the **read()** function to do the actual reading,
|
||
|
|
and call **getTemperature()** and **getHumidity()** to get the measured values.
|
||
|
|
Calling these latter again will return the same values until a new **read()** is done.
|
||
|
|
|
||
|
|
The **read()** call of this sensor is blocking for 80+ milliseconds (datasheet 7.4)
|
||
|
|
so the library also has a asynchronous interface. See below.
|
||
|
|
|
||
|
|
This library is based upon the DHT20 library which is leading in development.
|
||
|
|
The DHT20 also provides a bit more documentation and issues from the past.
|
||
|
|
- https://github.com/RobTillaart/DHT20
|
||
|
|
|
||
|
|
|
||
|
|
## I2C
|
||
|
|
|
||
|
|
#### Address
|
||
|
|
|
||
|
|
The sensor has a fixed address of **0x38**.
|
||
|
|
|
||
|
|
To use multiple AM2315C sensors one might use a multiplexer like the
|
||
|
|
- https://github.com/RobTillaart/TCA9548
|
||
|
|
|
||
|
|
|
||
|
|
#### Connection
|
||
|
|
|
||
|
|
Always check datasheet!
|
||
|
|
|
||
|
|
Front view
|
||
|
|
```
|
||
|
|
+-----------------+
|
||
|
|
RED -------- | VDD |
|
||
|
|
YELLOW -------- | SDA AM2315C |
|
||
|
|
BLACK -------- | GND |
|
||
|
|
WHITE -------- | SCL |
|
||
|
|
+-----------------+
|
||
|
|
```
|
||
|
|
|
||
|
|
|
||
|
|
## Interface
|
||
|
|
|
||
|
|
```cpp
|
||
|
|
#include "AM2315C.h"
|
||
|
|
```
|
||
|
|
|
||
|
|
#### Constructor
|
||
|
|
|
||
|
|
- **AM2315C(TwoWire \*wire = &Wire)** constructor, using a specific Wire (I2C bus).
|
||
|
|
- **bool begin(uint8_t dataPin, uint8_t clockPin)** begin for ESP32 et al, to set I2C bus pins.
|
||
|
|
- **bool begin()** initializer for non ESP32. Returns true if connected.
|
||
|
|
- **bool isConnected()** returns true if the address of the AM2315C can be seen on the I2C bus.
|
||
|
|
- **uint8_t getAddress()** returns the (fixed) address - convenience.
|
||
|
|
|
||
|
|
#### Core
|
||
|
|
|
||
|
|
- **int8_t read()** read the sensor and store the values internally.
|
||
|
|
Returns the status of the read which should be 0 == **AM2315C_OK**.
|
||
|
|
- **float getHumidity()** returns last Humidity read.
|
||
|
|
Multiple calls will return same value until a new **read()** is made.
|
||
|
|
- **float getTemperature()** returns last Temperature read.
|
||
|
|
Multiple calls will return same value until a new **read()** is made.
|
||
|
|
|
||
|
|
|
||
|
|
#### Offset
|
||
|
|
|
||
|
|
- **void setHumOffset(float offset = 0)** set an offset to calibrate the sensor (1st order).
|
||
|
|
Default offset is 0.
|
||
|
|
- **float getHumOffset()** return current humidity offset, default 0.
|
||
|
|
- **void setTempOffset(float offset = 0)** set an offset to calibrate the sensor (1st order).
|
||
|
|
Default offset is 0.
|
||
|
|
- **float getTempOffset()** return current temperature offset, default 0.
|
||
|
|
|
||
|
|
|
||
|
|
#### Asynchronous interface
|
||
|
|
|
||
|
|
There are two timings that need to be considered (from datasheet):
|
||
|
|
- time between requests = 1000 ms.
|
||
|
|
- time between request and data ready = 80 ms.
|
||
|
|
|
||
|
|
The async interface allows one to continue processing after a **requestData()** has been made.
|
||
|
|
Note there should be at least **1000 milliseconds** between subsequent requests.
|
||
|
|
|
||
|
|
With **bool isMeasuring()** one can check if a new measurement is ready.
|
||
|
|
Alternative is to delay for up to 80 ms.
|
||
|
|
If so the sensor can be read with **readData()**.
|
||
|
|
|
||
|
|
To interpret the read bits to temperature, humidity and status one needs to call **convert()** as last step.
|
||
|
|
|
||
|
|
|
||
|
|
- **int requestData()** signals the sensor to make a new measurement.
|
||
|
|
Note there must be at least 1000 milliseconds between requests!
|
||
|
|
- **int readData()** does the actual reading of the data.
|
||
|
|
- **int convert()** converts the read bits to temperature and humidity.
|
||
|
|
|
||
|
|
See the example **AM2315C_async.ino**
|
||
|
|
|
||
|
|
|
||
|
|
#### Status
|
||
|
|
|
||
|
|
- **uint8_t readStatus()** forced read of the status only.
|
||
|
|
This function blocks a few milliseconds to optimize communication.
|
||
|
|
- **bool isCalibrated()** idem, wrapper around **readStatus()**
|
||
|
|
- **bool isMeasuring()** idem, wrapper around **readStatus()**
|
||
|
|
- **bool isIdle()** idem, wrapper around **readStatus()**
|
||
|
|
- **int internalStatus()** returns the internal status of the sensor. (for debug).
|
||
|
|
|
||
|
|
| status bit | meaning |
|
||
|
|
|:------------:|:---------------------------|
|
||
|
|
| 7 | 1 = measurement, 0 = idle |
|
||
|
|
| 6 - 4 | unknown |
|
||
|
|
| 3 | 1 = calibrated, 0 = not |
|
||
|
|
| 2 - 0 | unknown |
|
||
|
|
|
||
|
|
|
||
|
|
#### Experimental resetSensor
|
||
|
|
|
||
|
|
Use with care!
|
||
|
|
|
||
|
|
- **uint8_t resetSensor()** if at startup the sensor does not return a status of 0x18,
|
||
|
|
three registers 0x1B, 0x1C and 0x1E need to be reset.
|
||
|
|
See datasheet 7.4 Sensor Reading Process, point 1.
|
||
|
|
There is no documentation about the meaning of these registers.
|
||
|
|
The code is based upon example code for the AHT20 (from manufacturer).
|
||
|
|
|
||
|
|
The call is needed to get the **read()** working well so it has been embedded into
|
||
|
|
the read calls. (0.2.0)
|
||
|
|
|
||
|
|
|
||
|
|
#### Timing
|
||
|
|
|
||
|
|
- **uint32_t lastRead()** last time the sensor is read in milliseconds since start.
|
||
|
|
- **uint32_t lastRequest()** last time a request is made to make a measurement.
|
||
|
|
|
||
|
|
|
||
|
|
#### Return codes
|
||
|
|
|
||
|
|
| name | value | notes |
|
||
|
|
|:-------------------------------|:-------:|:--------|
|
||
|
|
| AM2315C_OK | 00 | OK
|
||
|
|
| AM2315C_ERROR_CHECKSUM | -10 | values might be OK if they are like recent previous ones.
|
||
|
|
| AM2315C_ERROR_CONNECT | -11 | check connection
|
||
|
|
| AM2315C_MISSING_BYTES | -12 | check connection
|
||
|
|
| AM2315C_ERROR_BYTES_ALL_ZERO | -13 | check connection
|
||
|
|
| AM2315C_ERROR_READ_TIMEOUT | -14 |
|
||
|
|
| AM2315C_ERROR_LASTREAD | -15 | wait 1 second between reads
|
||
|
|
|
||
|
|
|
||
|
|
## Future
|
||
|
|
|
||
|
|
#### Must
|
||
|
|
|
||
|
|
- improve documentation.
|
||
|
|
- follow / sync DHT20 developments
|
||
|
|
- see https://github.com/RobTillaart/DHT20
|
||
|
|
- get hardware / sensor to test library
|
||
|
|
|
||
|
|
#### Should
|
||
|
|
|
||
|
|
#### Could
|
||
|
|
|
||
|
|
#### Wont
|
||
|
|
|
||
|
|
|