GY-63_MS5611/libraries/MCP_ADC/README.md

[![Arduino CI](https://github.com/RobTillaart/MCP_ADC/workflows/Arduino%20CI/badge.svg)](https://github.com/marketplace/actions/arduino_ci)
[![License: MIT](https://img.shields.io/badge/license-MIT-green.svg)](https://github.com/RobTillaart/MCP_ADC/blob/master/LICENSE)
[![GitHub release](https://img.shields.io/github/release/RobTillaart/MCP_ADC.svg?maxAge=3600)](https://github.com/RobTillaart/MCP_ADC/releases)

# MCP_ADC

Arduino library for MCP3002 MCP3004 MCP3008 MCP3202 MCP3204 MCP3208


## Description

This library reads the ADC ports of the MCP ADC convertors. 
The chips are communicates with SPI and support both hardware SPI or optional software SPI.


| type    | bits | channels | notes |
|:--------|:----:|:--------:|:------|
| MCP3002 |  10  |    2     |       |
| MCP3004 |  10  |    4     |       |
| MCP3008 |  10  |    8     |       |
| MCP3202 |  12  |    2     |       |
| MCP3204 |  12  |    4     |       |
| MCP3208 |  12  |    8     |       |


Current version allows manual override of the hardware SPI clock as the speed is not
optimized per ADC type. 

The MCP ADC allow single mode which compares voltage of a channel against GND.
Furthermore they allow a differential mode which compares two channels IN+ and IN- 
to each other. if the IN+ is equal or below IN- the ADC will return 0. 

Build into the library is a delta mode which is a software enhanced differential mode.
This delta mode can return negative values too. 


## Interface

If the pins are not set in the constructor, the class will automatically
use the hardware SPI, otherwise it will use a software SPI

- **MCP3002(dataIn, dataOut, clock)** constructor 10 bit ADC 2 channel
- **MCP3004(dataIn, dataOut, clock)** constructor 10 bit ADC 4 channel
- **MCP3008(dataIn, dataOut, clock)** constructor 10 bit ADC 8 channel
- **MCP3202(dataIn, dataOut, clock)** constructor 12 bit ADC 2 channel
- **MCP3204(dataIn, dataOut, clock)** constructor 12 bit ADC 4 channel
- **MCP3208(dataIn, dataOut, clock)** constructor 12 bit ADC 8 channel
- **void begin(select)** set select pin.
- **uint8_t channels()** returns the number of channels
- **int16_t maxValue()** returns maxReading of adc, e.g. 1023. 
This makes it easy to calculate relative measurements.
- **int16_t analogRead(channel)** reads the value of the channel
- **int16_t differentialRead(channel)** reads differential between two channels  
Check datasheet for details  
Note if the IN+ is equal or below IN- this function will return 0.
- **int16_t deltaRead(channel)** reads differential like above however it
will return a negative value if IN+ is below IN-.
- **void setSPIspeed(speed)** sets SPI clock in Hz, please read datasheet
of the ADC first to get optimal speed.
- **uint32_t getSPIspeed()** gets current speed in Hz


Differential channel table

| Channel | diff IN+ | diff IN- | MCP |
|:-------:|:--------:|:--------:|----:|
|   0     |    0     |    1     | 3x02/3x04/3x08 |
|   1     |    1     |    0     | 3x02/3x04/3x08 |
|   2     |    2     |    3     | 3x04/3x08 |
|   3     |    3     |    2     | 3x04/3x08 |
|   4     |    4     |    5     | 3x08 |
|   5     |    5     |    4     | 3x08 |
|   6     |    6     |    7     | 3x08 |
|   7     |    7     |    6     | 3x08 |


### debug

- **bool usesHWSPI()** returns true if HW SPI is used.


### ESP32 specific

- **void selectHSPI()** in case hardware SPI, the ESP32 has two options HSPI and VSPI.
- **void selectVSPI()** see above.
- **bool usesHSPI()** returns true if HSPI is used.
- **bool usesVSPI()** returns true if VSPI is used.
- **void setGPIOpins(clk, miso, mosi, select)** overrule GPIO pins of ESP32 for hardware SPI.


## About SPI Speed

See https://github.com/RobTillaart/MCP_ADC/issues/3

The default SPI speed is reduced to 1 MHz. 
This is the value recommended in the datasheet for 2.7V.

In a test with an ESP32 (3.3V) the library showed stable results 
at 4 Mhz and at 6 Mhz it was almost good.
 
The max value read at 6 MHz was 1020 instead of 1023  (MCP3008) 
which indicates that the last 2 bits got lost due to signal deformation.

| Board | Voltage |  safe  |  max  |
|:-----:|:-------:|:------:|:-----:|
| ESP32 |  2.7V   |  1 MHz | 4 Mhz |
| UNO   |  5.0V   |  2 MHz | 4 Mhz |


For hardware SPI the ESP32 uses the VSPI pins. (see ESP examples).


## Future / ideas / improvements

- testing, a lot ...
- get / setF(float A, float B) => float readF(channel)   output = A*value + B;
  it actually does float mapping. As it implies the same mapping for all it might 
  not be that useful
- analogRead (mask, int array\[8\] ) read ports (set in mask) in an array in one call.
- ESP32 - how to integrate the HSPI interface.


## Operations

See examples.