mirror of
https://github.com/RobTillaart/Arduino.git
synced 2024-10-03 18:09:02 -04:00
73 lines
2.0 KiB
Arduino
73 lines
2.0 KiB
Arduino
|
/**
|
||
|
|
* @file
|
||
|
|
* @Author Septillion (https://github.com/sseptillion)
|
||
|
|
* @date 2016-05-20
|
||
|
|
* @brief Example how to use buttonRead()
|
||
|
|
*
|
||
|
|
* Because of the quasi-bidirectional port on the PCF8574 it's
|
||
|
|
* possible to use the same pin as input and output at the same time.
|
||
|
|
*
|
||
|
|
* For this, connect the LED (or other device) between Vcc and the pin and
|
||
|
|
* a button between GND and the pin.
|
||
|
|
*
|
||
|
|
* In order to read the pin the output is shortly (460us @ normal I2C speed)
|
||
|
|
* set high during the read. So only use devices that can handle the small break
|
||
|
|
* in state. It's not visable for the human eye with a LED.
|
||
|
|
*
|
||
|
|
* buttonRead() can also be used for pins that are input only.
|
||
|
|
*
|
||
|
|
* In this example pin 0 of the PCF8574 (address 0x20) is used to blink a
|
||
|
|
* LED but at the same time it can be used to toggle the onboard LED of
|
||
|
|
* the Arduino.
|
||
|
|
*
|
||
|
|
* NOTE: The button will affect the LED on the same pin. The led will light up
|
||
|
|
* no matter the set output state when you press the button.
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include <PCF8574.h>
|
||
|
|
#include <Wire.h>
|
||
|
|
|
||
|
|
PCF8574 pcf20(0x20);
|
||
|
|
|
||
|
|
const byte onboardLed = 13;
|
||
|
|
const byte PcfButtonLedPin = 0;
|
||
|
|
|
||
|
|
unsigned int blinkMillis;
|
||
|
|
unsigned int buttonMillis;
|
||
|
|
|
||
|
|
void setup() {
|
||
|
|
Serial.begin(115200);
|
||
|
|
pcf20.begin();
|
||
|
|
|
||
|
|
pinMode(onboardLed, OUTPUT);
|
||
|
|
}
|
||
|
|
|
||
|
|
void loop() {
|
||
|
|
static bool state;
|
||
|
|
unsigned int currentMillis = millis();
|
||
|
|
|
||
|
|
//Limit button read to 20 times a second
|
||
|
|
//Fast enough for most buttons
|
||
|
|
//but this way you don't have a dimmer output because it's blanked during button read
|
||
|
|
//a read takes 460us t 16Mhz Arduino and normal I2C speed.
|
||
|
|
if(currentMillis - buttonMillis >= 50){
|
||
|
|
buttonMillis = currentMillis;
|
||
|
|
|
||
|
|
if(state != pcf20.readButton(PcfButtonLedPin)){
|
||
|
|
if(state){
|
||
|
|
//toggle the LED
|
||
|
|
digitalWrite(onboardLed, !digitalRead(onboardLed));
|
||
|
|
}
|
||
|
|
state = !state;
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|
||
|
|
//Lets blink the same output
|
||
|
|
if(currentMillis - blinkMillis >= 500){
|
||
|
|
//Update time
|
||
|
|
blinkMillis = currentMillis;
|
||
|
|
|
||
|
|
pcf20.toggle(PcfButtonLedPin);
|
||
|
|
Serial.println(pcf20.read8(), BIN);
|
||
|
|
}
|
||
|
|
}
|