GY-63_MS5611/libraries/DS18B20_RT/README.md

[![Arduino CI](https://github.com/RobTillaart/DS18B20/workflows/Arduino%20CI/badge.svg)](https://github.com/marketplace/actions/arduino_ci)
[![License: MIT](https://img.shields.io/badge/license-MIT-green.svg)](https://github.com/RobTillaart/DS18B20/blob/master/LICENSE)
[![GitHub release](https://img.shields.io/github/release/RobTillaart/DS18B20.svg?maxAge=3600)](https://github.com/RobTillaart/DS18B20/releases)

# DS18B20

Arduino library for the DS18B20 sensor - restricted to one sensor per pin.


## Arduino Temperature Control Library (ATCL)

This DS18B20 library is not a full featured library for the DS18B20 family.
This library supports only one DS18B20 per Arduino/ MCU pin.

If you need more functions or control over the DS18B20 family I refer to the library
of Miles Burton - https://github.com/milesburton/Arduino-Temperature-Control-Library

I'm a great fan of the above library however some time ago I needed to strip it down 
to save a few dozen bytes. I reworked that minimalistic version into a library and I 
added a number of Arduino examples to help you get started.


## Interface

The DS18B20 library supports only the DS18B20, only one sensor per pin, no parasite 
mode, no Fahrenheit and no alarm functions. The only feature the class supports is 
the asynchronous reading of the temperature by means of three core functions:

- **DS18B20(onewire)** constructor needs a reference to OneWire object.
- **bool begin(uint8_t retries = 3)** resets oneWire and set resolution to 9 bit.  
returns true if all is OK. there will be a number of retries to connect, default 3. 
- **void requestTemperatures()** trigger temperature comversion
- **bool isConversionComplete()** check if conversion is complete
- **float getTempC()** returns temperature
-127 = DEVICE_DISCONNECTED  
- **void setResolution(uint8_t res = 9)** res = 9..12 (9 is default)
- **bool getAddress()** returns true if the sensor is configured (available)

This allowed the class to be both minimal in size and non-blocking. In fact the class
has no support for a synchronous read in one call. This choice will teach people
how to work in a non-blocking way from the start.

Effort has been taken to keep the code, variables and function names compatible with 
ATCL library mentioned above. This way you can step over to that one with relatively
few problems when you need more functionality like multiple sensors on one pin.

Finally this library will probably make it easier to use a DS18B20 with processing 
boards or IC's with small memory footprint.


## Operation

This library supports only one DS18B20 per Arduino/ MCU pin.

```
    //  BOTTOM VIEW
    //
    //          PIN  MEANING
    //   /---+
    //  /  o |  1    GND
    //  |  o |  2    DATA
    //  \  o |  3    VCC
    //   \---+

```

Connect a pull-up resistor 4.7 KOhm between pin3 and pin2. 
When the wires are longer this resistor needs to be smaller.

Check examples.


### Pull up resistor

An **indicative** table for pull up resistors, (E12 series), to get started.

Note: thicker wires require smaller resistors (typically 1 step in E12 series) 


| Length        | - 5.0 Volt  | - 3.3 Volt |
|--------------:|------------:|----------:|
| 10cm (4")     | 10K0  | 6K8 |
| 20cm (8")     |  8K2  | 4K7 |
| 50cm (20")    |  4K7  | 3K3 | 
| 100cm (3'4")  |  3K3  | 2K2 | 
| 200cm (6'8")  |  2K2  | 1K0 | 
| 500cm (16'8") |  1K0  | \*  |  
| longer        |    *  | \*  |

\* = no info, smaller 


### Diagnosis notes

It was noted that the library sometimes give unexpected values, and keep 
sending these values.

This is due to the fact that by default the CRC is not checked to speed up reading. 
In fact, default only the two temperature registers are read.
By setting ```sensor.setConfig(DS18B20_CRC);``` the whole scratchpad is read
and the CRC can be checked. 


table of known "strange values" and actions one could take.
It is meant to start some diagnosis.

| value   | possible cause | optional action |
|:--------|:---------------|:----------------|
|  0.0000 | data line has no pull up            | use pull up |
| -0.0625 | data line is constantly pulled HIGH | check GND   |
| -128    | CRC error      | wrong pull up, bad sensor ? | 
| -127    | DISCONNECTED   | 

If a value occurs only once in a while, wiring is often the cause, 
or it can be caused by e.g. induction e.g. switching on a motor while 
sensor is read.


## Credits

Miles Burton who originally developed the Arduino Temperature Control Library.
and all people who contributed to that lib.